|
Colt 1851 Navy (58a)
|
|
|
Quantity in Basket:
None
Code: Colt_58a
Price: $68.00
Shipping Weight: 0.20 pounds
|
|
The Colt 1851 Navy .36 caliber cap and ball pistol grip
also has enough additional material to be used on the Cimmaron
"P" model, the EMF 1873 357 Magnum, and certain other
Colt clones. Most of these other guns have smaller grips, so that
you will need to use a 3/4-inch dowel wrapped with some 220
grit sandpaper to reduce the inside curve, or a medium grit
fingernail sanding stick to reduce the rear edge.
Or you can select the 2-piece set with mounting screw if
you prefer. This works whether the frame has a removable
backstrap or not. The 1-piece grip (3-piece kit) only
works if the backstrap is removable.
Please Note:
There are as many shapes and sizes for the 1851 Navy
as there are clones and originals combined. There is
NO WAY that I can guarantee this grip, or any single
action grip for that matter, will fit your gun UNLESS
you send me a tracing, a template, or the grips that
fit it now. I'd rather have a cut-out template made of
stiff paper than anything, but a tracing is fine if you
make it accurately.
I understand and count on the fact that when you
trace around the outline of a grip, the line will be a
little wider than the actual grip. Tombstone Grip Kits
are supposed to be slightly larger than your gun's frame
so you can accurately fit them to the frame with a little
light sanding. It is more difficult to trace around a
1-piece grip outline than it might be just to hold a piece
of stiff paper up to the gun frame, trace around the frame,
and cut out the template. Then trim it up so it is exactly
the size that your grips should be. I'll make sure that
I send grips that are at least that large, or slightly
larger. Otherwise, without this, I just have to go by
the size listed here and send you what you actually
order, since there's no way to determine if it is too
small or way too large or the wrong shape. That will
have to be determined by you (unless you send a tracing
or template, of course).
Some of the guns with smaller grips also have longer top portions
or wider bases. Any grip that fits within the outline and
is thus smaller in size can be duplicated by sanding down
this grip. It is somewhat of a universal replacement, for
1-piece Colt clones of various sizes. But be sure to check
the dimensions carefully before you order:
- Front vertical edge (A) = 1-1/16 inch
- Overall height (B) = 3-1/8 inch
- Width of base (C) 2-3/16 inch
- Midpoint of A to rear edge (D) = 2 inches
The 1-piece grip assembly is created when you have fitted
each panel to the gun, and the spacer to the inside of the frame.
One panel is taped in place, and the spacer glued to it with
a bit of 5-minute epoxy. After it has cured, the other grip
panel is epoxied to the spacer. The gun frame should be coated with
a film of vasoline to prevent any surplus epoxy from
sticking to it.
|
Related Item(s)
Code
|
Name
|
Price
|
Availability
|
|
Colt_81c
|
Colt Generic 3-pc SA Smaller (81c)
|
$68.00
|
|
Colt_57a
|
Colt Generic 3-pc SA Larger (57a)
|
$68.00
|
|
Colt_78a
|
Colt Generic 3-pc SA Thick (78a)
|
$68.00
|
|
Colt_151a
|
Generic Colt SA Blanks (151a)
|
$38.00
|
|
USN_Lg
|
US Navy 3/4-in
|
$14.00
|
|
Colt_58c
|
Colt 1851 Navy Pietta (58c)
|
$68.00
|
|
|